DIRECT BROWN 2
The
Chemical Identifier fields
include common identification numbers, the
NFPA diamond
U.S. Department of Transportation hazard labels, and a general
description of the chemical. The information in CAMEO Chemicals comes
from a variety of
data sources.
CAS Number | UN/NA Number |
---|---|
|
none |
DOT Hazard Label | USCG CHRIS Code |
data unavailable | none |
NIOSH Pocket Guide | International Chem Safety Card |
none | none |
NFPA 704
data unavailable
General Description
PHYSICAL DESCRIPTION: Reddish-brown solid or dark brown powder. (NTP, 1992)
The
Hazard fields
include
special hazard alerts
air and water
reactions, fire hazards, health hazards, a reactivity profile, and
details about
reactive groups assignments
and
potentially incompatible absorbents.
The information in CAMEO Chemicals comes from a variety of
data sources.
Reactivity Alerts
- Explosive
Air & Water Reactions
Azo dyes can be explosive when suspended in air at specific concentrations. Slightly soluble in water.
Fire Hazard
Flash point data for this chemical are not available, however, it is probably combustible. (NTP, 1992)
Health Hazard
No information available.
Reactivity Profile
DIRECT BROWN 2 is an azo compound. Azo, diazo, azido compounds can detonate. This applies in particular to organic azides that have been sensitized by the addition of metal salts or strong acids. Toxic gases are formed by mixing materials of this class with acids, aldehydes, amides, carbamates, cyanides, inorganic fluorides, halogenated organics, isocyanates, ketones, metals, nitrides, peroxides, phenols, epoxides, acyl halides, and strong oxidizing or reducing agents. Flammable gases are formed by mixing materials in this group with alkali metals. Explosive combination can occur with strong oxidizing agents, metal salts, peroxides, and sulfides.
Belongs to the Following Reactive Group(s)
Potentially Incompatible Absorbents
No information available.
The
Response Recommendation fields
include isolation and evacuation distances, as well as recommendations for
firefighting, non-fire response, protective clothing, and first aid. The
information in CAMEO Chemicals comes from a variety of
data sources.
Isolation and Evacuation
No information available.
Firefighting
Fires involving this compound can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. (NTP, 1992)
Non-Fire Response
SMALL SPILLS AND LEAKAGE: If you spill this chemical, you should dampen the solid spill material with water, then transfer the dampened material to a suitable container. Use absorbent paper dampened with water to pick up any remaining material. Seal your contaminated clothing and the absorbent paper in a vapor-tight plastic bag for eventual disposal. Wash all contaminated surfaces with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned.
STORAGE PRECAUTIONS: You should store this material in a refrigerator. (NTP, 1992)
STORAGE PRECAUTIONS: You should store this material in a refrigerator. (NTP, 1992)
Protective Clothing
RECOMMENDED RESPIRATOR: Where the neat test chemical is weighed and diluted, wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter. (NTP, 1992)
DuPont Tychem® Suit Fabrics
No information available.
First Aid
EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop.
SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing.
INGESTION: DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport the victim to a hospital. (NTP, 1992)
SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment.
INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing.
INGESTION: DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport the victim to a hospital. (NTP, 1992)
The
Physical Property fields
include properties such as vapor pressure and
boiling point, as well as explosive limits and
toxic exposure thresholds
The information in CAMEO Chemicals comes from a variety of
data sources.
Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Chemical Formula: |
|
Flash Point: data unavailable
Lower Explosive Limit (LEL): data unavailable
Upper Explosive Limit (UEL): data unavailable
Autoignition Temperature: data unavailable
Melting Point: data unavailable
Vapor Pressure: data unavailable
Vapor Density (Relative to Air): data unavailable
Specific Gravity: data unavailable
Boiling Point: data unavailable
Molecular Weight:
627.54
(NTP, 1992)
Water Solubility:
1 to 10 mg/mL
at 68°F
(NTP, 1992)
Ionization Energy/Potential: data unavailable
IDLH: data unavailable
AEGLs (Acute Exposure Guideline Levels)
No AEGL information available.ERPGs (Emergency Response Planning Guidelines)
No ERPG information available.PACs (Protective Action Criteria)
No PAC information available.
The
Regulatory Information fields
include information from
the U.S. Environmental Protection Agency's Title III Consolidated List of
Lists,
the U.S. Cybersecurity and Infrastructure Security Agency's Chemical Facility
Anti-Terrorism Standards,
and the U.S. Occupational Safety and Health Administration's
Process Safety Management of Highly Hazardous Chemicals Standard List
(see more about these
data sources).
EPA Consolidated List of Lists
No regulatory information available.CISA Chemical Facility Anti-Terrorism Standards (CFATS)
No regulatory information available.OSHA Process Safety Management (PSM) Standard List
No regulatory information available.
This section provides a listing of alternate names for this chemical,
including trade names and synonyms.
- AIREDALE BROWN MD
- AIZEN DIRECT BROWN MH
- AMANIL BROWN MR
- ATLANTIC BROWN M
- ATUL DIRECT BROWN MR
- ATUL DIRECT BROWN MY
- AZINE BROWN M
- AZOCARD BROWN M
- AZOMINE BROWN M
- BELAMINE FAST BROWN M
- BENCIDAL FAST BROWN M
- BENZANIL BROWN M
- BENZANOL BROWN M
- BENZO BROWN M
- BENZO BROWN MC
- BENZOIC ACID,5-((4'-((7-AMIONO-1-HYDROXY-3-SULFO-2-NAPHTHALENYL)AZO)(1,1'-BIPHENYL)-4-YL)AZO)-2-HYDROXY-,DISODIUM SALT
- BRASILAMINA FAST BROWN 3RA
- BROWN M
- C.I. 22311
- C.I. DIRECT BROWN 2
- C.I. DIRECT BROWN 2, DISODIUM SALT
- CALCOMINE BROWN MCW
- CHLORAMINE BROWN 2ME
- CHLORAMINE BROWN 2R
- CHLORAMINE BROWN M
- CHLORAMINE BROWN MR
- CHLORAZOL BROWN M
- CHLORAZOL BROWN MP
- CHROME LEATHER BROWN M
- COLUMBIA BROWN M
- CRESOTINE BROWN RC
- CUTAMIN BROWN CM
- DIACOTTON BROWN M
- DIAMINE BROWN
- DIAMINE BROWN M
- DIAMINE BROWN MBA-CF
- DIAMINE BROWN MR
- DIAMINE BROWN MRC
- DIAPHTAMINE BROWN M
- DIAZINE BROWN
- DIAZINE BROWN M
- DIAZINE BROWN MWR
- DIAZO BROWN MC
- DIAZOL BROWN M
- DIPHENYL BROWN
- DIPHENYL BROWN 3RB
- DIPHENYL BROWN BVV
- DIPHENYL BROWN V
- DIPHENYL FAST BROWN M
- DIPHENYL FAST BROWN MD
- DIRECT BROWN 2
- DIRECT BROWN 3RB
- DIRECT BROWN KKH
- DIRECT BROWN M
- DIRECT BROWN MB
- DIRECT BROWN MR
- DIRECT BROWN RC
- DIRECT BROWN RMR
- DIRECT FAST BROWN
- DIRECT FAST BROWN M
- DIRECT FAST BROWN MM
- DIRECT FAST BROWN V
- DIRECT FAST BROWN VR
- ENIANIL FAST BROWN M
- ERIE FAST BROWN 3RB
- ERIE FAST BROWN 3RBD
- FENAMIN BROWN M
- FIXANOL BROWN M
- HISPAMIN FAST BROWN 3R2B
- JAPANOL BROWN M
- KAYAKU DIRECT BROWN M
- MAHOGANY EMBL
- MITSUI DIRECT BROWN M
- NAPHTAMINE BROWN DC
- NEKLAMIN BROWN M
- NYANZA FAST BROWN M
- ORBAMIN BROWN MS
- PARAMINE FAST BROWN M
- PHENAMINE BROWN MB
- PHENO BROWN MRS
- PONTAMINE BROWN RMR
- SUGAI DIRECT BROWN M
- TERTRODIRECT BROWN MJ
- UNION BROWN DR
- UNION BROWN M
- VONDACEL BROWN M
Contact Us | Website Satisfaction Survey
Version 3.1.0 rev 1