Get the app in the App Store and on Google Play!

ACETONE CYANOHYDRIN, STABILIZED

6.1 - Poison Inhalation Hazard
Add to MyChemicals

The Chemical Identifier fields include common identification numbers, the NFPA diamond U.S. Department of Transportation hazard labels, and a general description of the chemical. The information in CAMEO Chemicals comes from a variety of data sources.
CAS Number UN/NA Number
  • 75-86-5   (ACETONE CYANOHYDRIN)
DOT Hazard Label USCG CHRIS Code
  • Poison Inhalation Hazard
NIOSH Pocket Guide International Chem Safety Card
Acetone cyanohydrinexternal_link
NFPA 704
Diamond Hazard Value Description
2
4 2
Blue Health 4 Can be lethal.
Red Flammability 2 Must be moderately heated or exposed to relatively high ambient temperatures before ignition can occur.
Yellow Instability 2 Readily undergoes violent chemical changes at elevated temperatures and pressures.
White Special
(NFPA, 2010)
General Description
A colorless liquid. Flash point 165°F. Lethal by inhalation and highly toxic or lethal by skin absorption. Density 7.8 lb / gal (less dense than water). Vapors heavier than air. Produces toxic oxides of nitrogen during combustion.

The Hazard fields include special hazard alerts air and water reactions, fire hazards, health hazards, a reactivity profile, and details about reactive groups assignments and potentially incompatible absorbents. The information in CAMEO Chemicals comes from a variety of data sources.
Reactivity Alerts
  • Water-Reactive
Air & Water Reactions
Soluble in water. May decompose on contact with water to form acetone and poisonous hydrogen cyanide.

Based on a scenario where the chemical is spilled into an excess of water (at least 5 fold excess of water), half of the maximum theoretical yield of Hydrogen Cyanide gas will be created in 12 minutes. Experimental details are in the following: "Development of the Table of Initial Isolation and Protective Distances for the 2008 Emergency Response Guidebook", ANL/DIS-09-2, D.F. Brown, H.M. Hartmann, W.A. Freeman, and W.D. Haney, Argonne National Laboratory, Argonne, Illinois, June 2009.
Fire Hazard
Too dangerous to health to expose fire fighters; a few whiffs of vapor could cause death; vapor or liquid could be fatal on penetrating normal protective clothing. Vapor forms explosive mixture with air. Decomposes when heated to 248F or at lower temperature under alkaline conditions, emitting highly toxic hydrogen cyanide. May react violently with water. Contact with sulfuric acid may cause it to explode. (EPA, 1998)
Health Hazard
This material is considered very hazardous and should only be handled under conditions that prevent any inhalation of vapor or skin contact. May be slightly irritating to skin and mucous membranes. (EPA, 1998)
Reactivity Profile
ACETONE CYANOHYDRIN readily decomposes to acetone and poisonous hydrogen cyanide gas on contact with water, acids (sulfuric acid) or when exposed to heat. Should be kept cool and slightly acidic (pH 4-5) [Sax, 2nd ed., 1965, p. 388]. Slowly dissociates to acetone, a flammable liquid, and hydrogen cyanide, a flammable poisonous gas, under normal storage and transportation conditions. Rate of dissociation increased by contact with alkalis and/or heat.
Belongs to the Following Reactive Group(s)
Potentially Incompatible Absorbents

Use caution: Liquids with this reactive group classification have been known to react with the absorbent listed below. More info about absorbents, including situations to watch out for...

  • Cellulose-Based Absorbents

The Response Recommendation fields include isolation and evacuation distances, as well as recommendations for firefighting, non-fire response, protective clothing, and first aid. The information in CAMEO Chemicals comes from a variety of data sources.
Isolation and Evacuation
Excerpt from ERG Guide 155 [Substances - Toxic and/or Corrosive (Flammable / Water-Sensitive)]:

IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.

SPILL: See ERG Table 1 - Initial Isolation and Protective Action Distances on the UN/NA 1541 datasheet.

FIRE: If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2020)
Firefighting
Wear air-supplied mask with canister approved for use with acrylonitrile in less than 2 percent concentration, rubber or plastic gloves, cover goggles or face mask, rubber boots, slicker suit, safety helmet.

Water may cause frothing if it gets below surface of liquid and turns to steam. Water fog gently applied to surface will cause frothing which will extinguish fire. Use water spray, dry chemical, alcohol foam, or carbon dioxide. Use water to keep fire-exposed containers cool, from a safe distance. (EPA, 1998)
Non-Fire Response
Excerpt from ERG Guide 155 [Substances - Toxic and/or Corrosive (Flammable / Water-Sensitive)]:

ELIMINATE all ignition sources (no smoking, flares, sparks or flames) from immediate area. All equipment used when handling the product must be grounded. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Stop leak if you can do it without risk. A vapor-suppressing foam may be used to reduce vapors. FOR CHLOROSILANES, use AFFF alcohol-resistant medium-expansion foam to reduce vapors. DO NOT GET WATER on spilled substance or inside containers. Use water spray to reduce vapors or divert vapor cloud drift. Avoid allowing water runoff to contact spilled material. Prevent entry into waterways, sewers, basements or confined areas.

SMALL SPILL: Cover with DRY earth, DRY sand or other non-combustible material followed with plastic sheet to minimize spreading or contact with rain. Use clean, non-sparking tools to collect material and place it into loosely covered plastic containers for later disposal. (ERG, 2020)
Protective Clothing
Excerpt from NIOSH Pocket Guide for Acetone cyanohydrinexternal link:

Skin: PREVENT SKIN CONTACT - Wear appropriate personal protective clothing to prevent skin contact.

Eyes: PREVENT EYE CONTACT - Wear appropriate eye protection to prevent eye contact.

Wash skin: WHEN CONTAMINATED - The worker should immediately wash the skin when it becomes contaminated.

Remove: WHEN WET OR CONTAMINATED - Work clothing that becomes wet or significantly contaminated should be removed and replaced.

Change: No recommendation is made specifying the need for the worker to change clothing after the workshift.

Provide:
• EYEWASH - Eyewash fountains should be provided in areas where there is any possibility that workers could be exposed to the substances; this is irrespective of the recommendation involving the wearing of eye protection.
• QUICK DRENCH - Facilities for quickly drenching the body should be provided within the immediate work area for emergency use where there is a possibility of exposure. [Note: It is intended that these facilities provide a sufficient quantity or flow of water to quickly remove the substance from any body areas likely to be exposed. The actual determination of what constitutes an adequate quick drench facility depends on the specific circumstances. In certain instances, a deluge shower should be readily available, whereas in others, the availability of water from a sink or hose could be considered adequate.] (NIOSH, 2023)
DuPont Tychem® Suit Fabrics
Tychem® Fabric Legend
QS = Tychem 2000 SFR
QC = Tychem 2000
SL = Tychem 4000
C3 = Tychem 5000
TF = Tychem 6000
TP = Tychem 6000 FR
RC = Tychem RESPONDER® CSM
TK = Tychem 10000
RF = Tychem 10000 FR
Testing Details
The fabric permeation data was generated for DuPont by a third party laboratory. Permeation data for industrial chemicals is obtained per ASTM F739. Normalized breakthrough times (the time at which the permeation rate exceeds 0.1 μg/cm2/min) are reported in minutes. All chemicals have been tested between approximately 20°C and 27°C unless otherwise stated. All chemicals have been tested at a concentration of greater than 95% unless otherwise stated.
Chemical warfare agents (Lewisite, Sarin, Soman, Sulfur Mustard, Tabun and VX Nerve Agent) have been tested at 22°C and 50% relative humidity per military standard MIL-STD-282. "Breakthrough time" for chemical warfare agents is defined as the time when the cumulative mass which permeated through the fabric exceeds the limit in MIL-STD-282 [either 1.25 or 4.0 μg/cm2].
A Caution from DuPont
This information is based upon technical data that DuPont believes to be reliable on the date issued. It is subject to revision as additional knowledge and experience are gained. The information reflects laboratory performance of fabrics, not complete garments, under controlled conditions. It is intended for informational use by persons having technical skill for evaluation under their specific end-use conditions, at their own discretion and risk. It is the user's responsibility to determine the level of toxicity and the proper personal protective equipment needed. Anyone intending to use this information should first verify that the garment selected is suitable for the intended use. In many cases, seams and closures have shorter breakthrough times and higher permeation rates than the fabric. If fabric becomes torn,abraded or punctured, or if seams or closures fail, or if attached gloves, visors, etc. are damaged, end user should discontinue use of garment to avoid potential exposure to chemical. Since conditions of use are outside our control, DuPont makes no warranties, express or implied, including, without limitation, no warranties of merchantability or fitness for a particular use and assume no liability in connection with any use of this information. This information is not intended as a license to operate under or a recommendation to infringe any patent, trademark or technical information of DuPont or others covering any material or its use.
Normalized Breakthrough Times (in Minutes)
Chemical CAS Number State QS QC SL C3 TF TP RC TK RF
Acetone cyanohydrin 75-86-5 Liquid >480 >480 >480 >480 >480
Cyanopropan-2-ol, 2- 75-86-5 Liquid >480 >480 >480 >480 >480
Hydroxy 2-methylpropionitrile, 2- 75-86-5 Liquid >480 >480 >480 >480 >480
Hydroxy isobutyronitrile 75-86-5 Liquid >480 >480 >480 >480 >480
> indicates greater than.

Special Warning from DuPont: Tychem® and Tyvek® fabrics should not be used around heat, flames, sparks or in potentially flammable or explosive environments. Only...

...Tychem® ThermoPro, Tychem® Reflector® and Tychem® TK styles 600T/601T (with aluminized outer suit) garments are designed and tested to help reduce burn injury during escape from a flash fire. Users of Tychem® ThermoPro, Tychem® Reflector® and Tychem® TK styles 600T/601T (with aluminized outer suit) garments should not knowingly enter an explosive environment. Tychem® garments with attached socks must be worn inside protective outer footwear and are not suitable as outer footwear. These attached socks do not have adequate durability or slip resistance to be worn as the outer foot covering.

(DuPont, 2023)

First Aid
Warning: Effects, including skin reactions, may be delayed. Caution is advised. Vital signs should be monitored closely. Heart palpitation may begin within minutes after exposure.

Note: Acetone cyanohydrin is very readily absorbed through the skin.

Signs and Symptoms of Acetone Cyanohydrin Exposure: Signs and symptoms of acute exposure to acetone cyanohydrin may include hypertension (high blood pressure) and tachycardia (rapid heart rate), followed by hypotension (low blood pressure) and bradycardia (slow heart rate). Cherry-red mucous membranes and blood, cardiac arrhythmias, and other cardiac abnormalities are common. Cyanosis (blue tint to the skin and mucous membranes) is not a consistent finding. Tachypnea (rapid respiratory rate) may be followed by respiratory depression. Lung hemorrhage and pulmonary edema may also occur. Headache, vertigo (dizziness), agitation, and giddiness may be followed by combative behavior, convulsions, paralysis, protruding eyeballs, dilated and unreactive pupils, and coma. Acetone cyanohydrin is irritating to the skin and mucous membranes. Lacrimation (tearing) and a burning sensation of the mouth and throat are common. Excessive salivation, nausea, and vomiting may also occur.

Emergency Life-Support Procedures: Acute exposure to acetone cyanohydrin may require decontamination and life support for the victims. Emergency personnel should wear protective clothing appropriate to the type and degree of contamination. Air-purifying or supplied-air respiratory equipment should also be worn, as necessary. Rescue vehicles should carry supplies such as plastic sheeting and disposable plastic bags to assist in preventing spread of contamination.

Inhalation Exposure:
1. Move victims to fresh air. Emergency personnel should avoid self-exposure to acetone cyanohydrin.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with acetone cyanohydrin-contaminated persons or their gastric contents may result in self-poisoning.
3. RUSH to a health care facility!
4. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.

Dermal/Eye Exposure:
1. Remove victims from exposure. Emergency personnel should avoid self-exposure to acetone cyanohydrin.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with acetone cyanohydrin-contaminated persons or their gastric contents may result in self-poisoning.
3. RUSH to a health care facility!
4. Remove contaminated clothing as soon as possible.
5. If eye exposure has occurred, eyes must be flushed with lukewarm water for at least 15 minutes.
6. Wash exposed skin areas twice with soap and water.
7. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.

Ingestion Exposure:
1. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. IMMEDIATELY begin administering 100% oxygen to all victims. Monitor victims for respiratory distress.Warning: To prevent self-poisoning, avoid mouth-to-mouth breathing; use a forced-oxygen mask. Direct oral contact with acetone cyanohydrin contaminated persons or their gastric contents may result in self-poisoning.
2. RUSH to a health care facility!
3. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
4. DO NOT induce vomiting or attempt to neutralize!
5. Activated charcoal may be administered if victims are conscious and alert. Use 15 to 30 g (1/2 to 1 oz) for children, 50 to 100 g (1-3/4 to 3-1/2 oz) for adults, with 125 to 250 mL (1/2 to 1 cup) of water.
6. Give the victims water or milk: children up to 1 year old, 125 mL (4 oz or 1/2 cup); children 1 to 12 years old, 200 mL (6 oz or 3/4 cup); adults, 250 mL (8 oz or 1 cup). Water or milk should be given only if victims are conscious and alert. (EPA, 1998)

The Physical Property fields include properties such as vapor pressure and boiling point, as well as explosive limits and toxic exposure thresholds The information in CAMEO Chemicals comes from a variety of data sources.

Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Chemical Formula:
  • C4H7NO
Flash Point: 165°F (EPA, 1998)
Lower Explosive Limit (LEL): 2.2 % (EPA, 1998)
Upper Explosive Limit (UEL): 12 % (EPA, 1998)
Autoignition Temperature: 1270°F (USCG, 1999)
Melting Point: -2.2°F (EPA, 1998)
Vapor Pressure: 0.8 mmHg at 68°F (EPA, 1998)
Vapor Density (Relative to Air): 2.93 (EPA, 1998) - Heavier than air; will sink
Specific Gravity: 0.9267 at 77°F (EPA, 1998) - Less dense than water; will float
Boiling Point: 180°F at 23 mmHg (EPA, 1998)
Molecular Weight: 85.1 (EPA, 1998)
Water Solubility: greater than or equal to 100 mg/mL at 68°F (NTP, 1992)
Ionization Energy/Potential: data unavailable
IDLH: data unavailable

AEGLs (Acute Exposure Guideline Levels)

Final AEGLs for Acetone cyanohydrin (75-86-5)
Exposure Period AEGL-1 AEGL-2 AEGL-3
10 minutes 2.5 ppm 17 ppm 27 ppm
30 minutes 2.5 ppm 10 ppm 21 ppm
60 minutes 2 ppm 7.1 ppm 15 ppm
4 hours 1.3 ppm 3.5 ppm 8.6 ppm
8 hours 1 ppm 2.5 ppm 6.6 ppm
(NAC/NRC, 2023)

ERPGs (Emergency Response Planning Guidelines)

No ERPG information available.

PACs (Protective Action Criteria)

Chemical PAC-1 PAC-2 PAC-3
Methyllactonitrile, 2-; (Acetone cyanohydrin) (75-86-5) 2 ppm 7.1 ppm 15 ppm LEL = 22000 ppm
(DOE, 2018)

The Regulatory Information fields include information from the U.S. Environmental Protection Agency's Title III Consolidated List of Lists, the U.S. Cybersecurity and Infrastructure Security Agency's Chemical Facility Anti-Terrorism Standards, and the U.S. Occupational Safety and Health Administration's Process Safety Management of Highly Hazardous Chemicals Standard List (see more about these data sources).

EPA Consolidated List of Lists

Regulatory Name CAS Number/
313 Category Code
EPCRA 302
EHS TPQ
EPCRA 304
EHS RQ
CERCLA RQ EPCRA 313
TRI
RCRA
Code
CAA 112(r)
RMP TQ
2-Methyllactonitrile 75-86-5 1000 pounds 10 pounds 10 pounds 313 P069
Acetone cyanohydrin 75-86-5 1000 pounds 10 pounds 10 pounds X P069

(EPA List of Lists, 2022)

CISA Chemical Facility Anti-Terrorism Standards (CFATS)

RELEASE THEFT SABOTAGE
Chemical of Interest CAS Number Min Conc STQ Security
Issue
Min Conc STQ Security
Issue
Min Conc STQ Security
Issue
Acetone cyanohydrin, stabilized 75-86-5 ACG APA sabotage/ contamination

(CISA, 2007)

OSHA Process Safety Management (PSM) Standard List

No regulatory information available.

This section provides a listing of alternate names for this chemical, including trade names and synonyms.
  • ACETONE CYANHYDRIN
  • ACETONE CYANOHYDRIN
  • ACETONE CYANOHYDRIN, STABILIZED
  • ALPHA-HYDROXY ISOBUTRONITRILE
  • ALPHA-HYDROXYISOBUTYRONITRILE
  • 2-CYANO-2-HYDROXYPROPANE
  • 2-CYANO-2-PROPANOL
  • CYANOHYDRIN-2-PROPANONE
  • 2-HYDROXY-2-CYANOPROPANE
  • 2-HYDROXY-2-METHYL-PROPIONITRILE
  • 2-HYDROXY-2-METHYLPROPANENITRILE
  • 2-HYDROXY-2-METHYLPROPIONITRILE
  • 2-HYDROXYISOBUTYRONITRILE
  • LACTONITRILE, 2-METHYL-
  • 2-METHYL-2-HYDROXYPROPIONITRILE
  • 2-METHYLACTONITRILE
  • 2-METHYLLACTONITRILE
  • PROPANENITRILE, 2-HYDROXY-2-METHYL-
  • PROPANENITRILE, 2-HYRODXY-2-METHYL
  • 2-PROPANONE, CYANOHYDRIN
  • USAF RH-8

Version 3.0.0