Get the app in the App Store and on Google Play!

ENDOSULFAN

6.1 - Poison
Add to MyChemicals

The Chemical Identifier fields include common identification numbers, the NFPA diamond U.S. Department of Transportation hazard labels, and a general description of the chemical. The information in CAMEO Chemicals comes from a variety of data sources.
CAS Number UN/NA Number
  • 115-29-7
DOT Hazard Label USCG CHRIS Code
  • Poison
NIOSH Pocket Guide International Chem Safety Card
Endosulfanexternal_link
NFPA 704
data unavailable
General Description
A brown or colorless crystalline solid with a pungent odor. More dense than water and nearly insoluble in water. Toxic by inhalation, skin absorption, or ingestion. Used as a pesticide, fungicide or herbicide.

The Hazard fields include special hazard alerts air and water reactions, fire hazards, health hazards, a reactivity profile, and details about reactive groups assignments and potentially incompatible absorbents. The information in CAMEO Chemicals comes from a variety of data sources.
Reactivity Alerts
none
Air & Water Reactions
Sightly soluble in water. Slowly hydrolyzes to form sulfur dioxide and a diol; hydrolyzes more rapidly under basic or acidic conditions.
Fire Hazard
Container may explode in heat of fire. Fire or run off from fire control water may release irritating or poisonous gases. Slowly oxidizes in air. Do not store at temperature below 20F. (EPA, 1998)
Health Hazard
It is very toxic. The probable oral lethal dose is 50 to 500 mg/kg, or 1 teaspoonful to 1 ounce for a 150 lb. person. (EPA, 1998)
Reactivity Profile
ENDOSULFAN is an organochlorine, cyclodiene derivative. It is also a sulfite ester. Halogenated aliphatic or cyclic alkane compounds are moderately or very reactive. Halogenated organics generally become less reactive as more of their hydrogen atoms are replaced with halogen atoms. As endosulfan is rather highly substituted it may be resistant to reaction. However, materials in this group are incompatible with strong oxidizing and reducing agents. Also, they may be incompatible with many amines, nitrides, azo/diazo compounds, alkali metals, and epoxides. As an ester, it will hydrolyze to form sulfur dioxide and diol; reaction is more rapid under basic conditions.
Belongs to the Following Reactive Group(s)
Potentially Incompatible Absorbents

Use caution: Liquids with this reactive group classification have been known to react with the absorbent listed below. More info about absorbents, including situations to watch out for...

  • Dirt/Earth

The Response Recommendation fields include isolation and evacuation distances, as well as recommendations for firefighting, non-fire response, protective clothing, and first aid. The information in CAMEO Chemicals comes from a variety of data sources.
Isolation and Evacuation
Excerpt from ERG Guide 151 [Substances - Toxic (Non-Combustible)]:

IMMEDIATE PRECAUTIONARY MEASURE: Isolate spill or leak area in all directions for at least 50 meters (150 feet) for liquids and at least 25 meters (75 feet) for solids.

SPILL: Increase the immediate precautionary measure distance, in the downwind direction, as necessary.

FIRE: If tank, rail car or tank truck is involved in a fire, ISOLATE for 800 meters (1/2 mile) in all directions; also, consider initial evacuation for 800 meters (1/2 mile) in all directions. (ERG, 2020)
Firefighting
Keep unnecessary people away; isolate hazard area and deny entry. Stay upwind; keep out of low areas. Ventilate closed spaces before entering them. Wear positive pressure breathing apparatus and special protective clothing. Remove and isolate contaminated clothing at the site.

Extinguish fire using agent suitable for type of surrounding fire. (Material itself does not burn or burns with difficulty.) Use water in flooding quantities as fog. Use alcohol foam, carbon dioxide or dry chemical. (EPA, 1998)
Non-Fire Response
Excerpt from ERG Guide 151 [Substances - Toxic (Non-Combustible)]:

Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Stop leak if you can do it without risk. Prevent entry into waterways, sewers, basements or confined areas. Cover with plastic sheet to prevent spreading. Absorb or cover with dry earth, sand or other non-combustible material and transfer to containers. DO NOT GET WATER INSIDE CONTAINERS. (ERG, 2020)
Protective Clothing
Excerpt from NIOSH Pocket Guide for Endosulfanexternal link:

Skin: PREVENT SKIN CONTACT - Wear appropriate personal protective clothing to prevent skin contact.

Eyes: PREVENT EYE CONTACT - Wear appropriate eye protection to prevent eye contact.

Wash skin: WHEN CONTAMINATED - The worker should immediately wash the skin when it becomes contaminated.

Remove: WHEN WET OR CONTAMINATED - Work clothing that becomes wet or significantly contaminated should be removed and replaced.

Change: DAILY - Workers whose clothing may have become contaminated should change into uncontaminated clothing before leaving the work premises.

Provide:
• EYEWASH - Eyewash fountains should be provided in areas where there is any possibility that workers could be exposed to the substances; this is irrespective of the recommendation involving the wearing of eye protection.
• QUICK DRENCH - Facilities for quickly drenching the body should be provided within the immediate work area for emergency use where there is a possibility of exposure. [Note: It is intended that these facilities provide a sufficient quantity or flow of water to quickly remove the substance from any body areas likely to be exposed. The actual determination of what constitutes an adequate quick drench facility depends on the specific circumstances. In certain instances, a deluge shower should be readily available, whereas in others, the availability of water from a sink or hose could be considered adequate.] (NIOSH, 2023)
DuPont Tychem® Suit Fabrics
No information available.
First Aid
Signs and Symptoms of Acute Endosulfan Exposure: Ingestion of endosulfan may result in nausea, vomiting, and diarrhea. Dizziness, agitation, nervousness, tremor, incoordination, and convulsions may also occur. Central nervous system depression may terminate in respiratory failure. Contact with endosulfan may irritate or burn the skin, eyes, and mucous membranes.

Emergency Life-Support Procedures: Acute exposure to endosulfan may require decontamination and life support for the victims. Emergency personnel should wear protective clothing appropriate to the type and degree of contamination. Air-purifying or supplied-air respiratory equipment should also be worn, as necessary. Rescue vehicles should carry supplies such as plastic sheeting and disposable plastic bags to assist in preventing spread of contamination.

Inhalation Exposure:
1. Move victims to fresh air. Emergency personnel should avoid self-exposure to endosulfan.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer oxygen or other respiratory support.
3. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
4. Transport to a health care facility.

Dermal/Eye Exposure:
1. Remove victims from exposure. Emergency personnel should avoid self- exposure to endosulfan.
2. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer oxygen or other respiratory support.
3. Remove contaminated clothing as soon as possible.
4. If eye exposure has occurred, eyes must be flushed with lukewarm water for at least 15 minutes.
5. Wash exposed skin areas three times. An initial soap and water wash should be followed by an alcohol wash. The third wash should again be with soap and water.
6. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
7. Transport to a health care facility.

Ingestion Exposure:
1. Evaluate vital signs including pulse and respiratory rate, and note any trauma. If no pulse is detected, provide CPR. If not breathing, provide artificial respiration. If breathing is labored, administer oxygen or other respiratory support.
2. Obtain authorization and/or further instructions from the local hospital for administration of an antidote or performance of other invasive procedures.
3. Vomiting may be induced with syrup of Ipecac. If elapsed time since ingestion of endosulfan is unknown or suspected to be greater than 30 minutes, do not induce vomiting and proceed to Step
4.Ipecac should not be administered to children under 6 months of age.Warning: Ingestion of endosulfan may result in sudden onset of seizures or loss of consciousness. Syrup of Ipecac should be administered only if victims are alert, have an active gag-reflex, and show no signs of impending seizure or coma. If ANY uncertainty exists, proceed to Step
4.The following dosages of Ipecac are recommended: children up to 1 year old, 10 mL (1/3 oz); children 1 to 12 years old, 15 mL (1/2 oz); adults, 30 mL (1 oz). Ambulate (walk) the victims and give large quantities of water. If vomiting has not occurred after 15 minutes, Ipecac may be readministered. Continue to ambulate and give water to the victims. If vomiting has not occurred within 15 minutes after second administration of Ipecac, administer activated charcoal.
4. Activated charcoal may be administered if victims are conscious and alert. Use 15 to 30 g (1/2 to 1 oz) for children, 50 to 100 g (1-3/4 to 3-1/2 oz) for adults, with 125 to 250 mL (1/2 to 1 cup) of water.
5. Promote excretion by administering a saline cathartic or sorbitol to conscious and alert victims. Children require 15 to 30 g (1/2 to 1 oz) of cathartic; 50 to 100 g (1-3/4 to 3-1/2 oz) is recommended for adults.
6. Transport to a health care facility. (EPA, 1998)

The Physical Property fields include properties such as vapor pressure and boiling point, as well as explosive limits and toxic exposure thresholds The information in CAMEO Chemicals comes from a variety of data sources.

Note: For Vapor Density and Specific Gravity, comparing the value to 1.0 can tell you if the chemical will likely sink/rise in air or sink/float in fresh water (respectively). Short phrases have been added to those values below as an aid. However, make sure to also consider the circumstances of a release. The Vapor Density comparisons are only valid when the gas escaping is at the same temperature as the surrounding air itself. If the chemical is escaping from a container where it was pressurized or refrigerated, it may first escape and behave as a heavy gas and sink in the air (even if it has a Vapor Density value less than 1). Also, the Specific Gravity comparisons are for fresh water (density 1.0 g/mL). If your spill is in salt water (density about 1.027 g/mL), you need to adjust the point of comparison. There are some chemicals that will sink in fresh water and float in salt water.
Chemical Formula:
  • C9H6Cl6O3S
Flash Point: data unavailable
Lower Explosive Limit (LEL): data unavailable
Upper Explosive Limit (UEL): data unavailable
Autoignition Temperature: data unavailable
Melting Point: 158 to 212°F Range of values given is for a mixture of isomers (a isomer 228.7°F; b isomer 415.9°F). (EPA, 1998)
Vapor Pressure: 1e-05 mmHg at 77°F (EPA, 1998)
Vapor Density (Relative to Air): data unavailable
Specific Gravity: 1.745 at 68°F (EPA, 1998) - Denser than water; will sink
Boiling Point: Decomposes (NIOSH, 2023)
Molecular Weight: 406.95 (EPA, 1998)
Water Solubility: less than 1 mg/mL at 73°F (NTP, 1992)
Ionization Energy/Potential: data unavailable
IDLH: data unavailable

AEGLs (Acute Exposure Guideline Levels)

No AEGL information available.

ERPGs (Emergency Response Planning Guidelines)

No ERPG information available.

PACs (Protective Action Criteria)

Chemical PAC-1 PAC-2 PAC-3
Endosulfan (115-29-7) 0.3 mg/m3 0.8 mg/m3 180 mg/m3
(DOE, 2018)

The Regulatory Information fields include information from the U.S. Environmental Protection Agency's Title III Consolidated List of Lists, the U.S. Cybersecurity and Infrastructure Security Agency's Chemical Facility Anti-Terrorism Standards, and the U.S. Occupational Safety and Health Administration's Process Safety Management of Highly Hazardous Chemicals Standard List (see more about these data sources).

EPA Consolidated List of Lists

Regulatory Name CAS Number/
313 Category Code
EPCRA 302
EHS TPQ
EPCRA 304
EHS RQ
CERCLA RQ EPCRA 313
TRI
RCRA
Code
CAA 112(r)
RMP TQ
Endosulfan 115-29-7 10/10000 pounds 1 pound 1 pound P050
Endosulfan and Metabolites N.A. &

(EPA List of Lists, 2022)

CISA Chemical Facility Anti-Terrorism Standards (CFATS)

No regulatory information available.

OSHA Process Safety Management (PSM) Standard List

No regulatory information available.

This section provides a listing of alternate names for this chemical, including trade names and synonyms.
  • ALPHA, BETA-1,2,3,4,7,7-HEXACHLOROBICYCLO)2.2.1)-2-HEPTENE-5,6-BISOXY-METHYLENE SULFITE
  • ALPHA, BETA-1,2,3,4,7,7-HEXACHLOROBICYCLO[2.2.1]-2-HEPTENE-5,6-BISOXYMETHYLENE SULFITE
  • AS 4314
  • BENZOEPIN
  • BEOSIT
  • BIO 5,462
  • BIO 5,642
  • CHLORTHEPIN
  • CHLORTHIEPIN
  • CRISULFAN
  • CYCLODAN
  • DEVISULPHAN
  • ENDOCEL
  • ENDOSOL
  • ENDOSULFAN
  • ENDOSULFAN 35EC
  • ENDOSULFAN AND METABOLITES
  • ENDOSULPHAN
  • ENDOTAF
  • ENSURE
  • ENT 23,979
  • ENT 23979
  • FMC 5462
  • 6,7,8,9,10-HEXACHLORO-1,5,5A,6,9,9A-HEXACHLORO-6,9-METHANO- 2,4,3-BENZO-DIOXATHIEPIN-3-OXIDE
  • 6,7,8,9,10,10-HEXACHLORO-1,5,5A,6,9,9A-HEXAHYDRO-6,9-METHANO-2,4,3- BENZO[E]DIOXATHIEPIN-3-OXIDE
  • 6,7,8,9 10,10-HEXACHLORO-1,5,5A,6,9,9A-HEXAHYDRO-6,9-METHANO-2,4,3-BENZODIOXATHIEPIN- 3-OXIDE
  • 6,7,8,9,10,10-HEXACHLORO-1,5,5A,6,9,9A-HEXAHYDRO-6,9-METHANO-2,4,3-BENZODIOXATHIEPIN-3-OXIDE
  • 1,4,5,6,7,7-HEXACHLORO-5-NORBORNENE-2,3-DIMETHANOL CYCLIC SULFITE
  • 1,4,5,6,7,7-HEXACHLORO-5-NORBORNENE-2,3-DIMETHANOL, CYCLIC SULFATE
  • 1,4,5,6,7,7-HEXACHLORO-8,9,10-TRINORBORN-5-EN-2,3-YLENEDIMETHYL SULPHITE
  • 1,2,3,4,7,7-HEXACHLOROBICYCLO(2.2.1)HEPTEN-5,6-BIOXYMETHYLENE SULFITE
  • 1,2,3,4,7,7-HEXACHLOROBICYCLO-[2.2.1]-HEPTEN-5,6-BISOXYMETHYLENE SULFITE
  • 1,2,3,4,7,7-HEXACHLOROBICYCLO[2.2.1]-2-HEPTENE-5,6-BISOXYMETHYLENE SULFITE
  • 1,2,3,4,7,7-HEXACHLOROBICYCLO[2.2.1]HEPTEN-5,6-BIOXYMETHYLENESULFITE
  • HEXACHLOROHEXAHYDROMETHANO 2,4,3-BENZODIOXATHIEPIN-3-OXIDE
  • HEXACHLOROHEXAHYDROMETHANO-2,4,3-BENZODIOXATHIEPIN-3-OXIDE
  • HILDAN
  • HOE 2,671
  • HOE 2671
  • INSECTOPHENE
  • KOP-THIODAN
  • MALIX
  • 6,9-METHANO-2,4,3-BENZODIOXATHIEPIN, 6,7,8,9,10,10-HEXACHLORO-1,5,5A,6,9,9A-HEXAHYDRO-, 3-OXIDE
  • NCI C00566
  • NCI-C00566
  • NIA 5462
  • NIAGARA 5,462
  • NIAGARA 5462
  • NIAGRA 5462
  • 5-NORBORNENE-2,3-DIMETHANOL, 1,4,5,6,7,7-HEXACHLORO-, CYCLIC SULFITE
  • OMS 570
  • PHASER
  • SD 4314
  • SULFUROUS ACID, CYCLIC ESTER WITH 1,4,5,6,7,7-HEXACHLORO-5- NORBORNENE-2,3-DIMETHANOL
  • SULFUROUS ACID, CYCLIC ESTER WITH 1,4,5,6,7,7-HEXACHLORO-5-NORBORNENE-2-DIMETHANOL
  • THIFOR
  • THIMUL
  • THIODAN
  • THIODAN 35
  • THIODAN 35EC
  • THIODAN®
  • THIOFOR
  • THIOMUL
  • THIOMUL THIONEX
  • THIONEX
  • THIOSULFAN
  • THIOSULFAN TIONEL
  • THIOTOX
  • THIOTOX (INSECTICIDE)
  • THIOTOX[INSECTICIDE]
  • TIONEL
  • TIONEX
  • TIOVEL

Version 3.0.0